2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 393

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 393

* Right front speaker output (+) - terminal 7 X2

* Right front speaker output (-) - terminal 6 X2

* Left rear speaker output (+) - terminal 15 X2

* Left rear speaker output (-) - terminal 14 X2

* Right rear speaker output (+) - terminal 16 X2

* Right rear speaker output (-) - terminal 8 X2

* Front center speaker output (+) - terminal 13 X2

* Front center speaker output (-) - terminal 12 X2

* Right rear midrange speaker output (+) - terminal 3 X2

* Right rear midrange speaker output (-) - terminal 2 X2

* Left rear midrange speaker output (+) - terminal 11 X2

* Left rear midrange speaker output (-) - terminal 10 X2

* Left or rear subwoofer speaker output (+) - terminal 1 X1

* Left or rear subwoofer speaker output (-) - terminal 2 X1

* Right subwoofer speaker output (+) - terminal 7 X1

* Right subwoofer speaker output (-) - terminal 3 X1

瀚慖f greater than the specified range, test both circuits of the affected speaker for a short to voltage.

3. Radio OFF, test for infinite resistance between the appropriate signal circuit terminal listed below and ground:

* Left front speaker output (+) - terminal 4 X2

* Left front speaker output (-) - terminal 5 X2

* Right front speaker output (+) - terminal 7 X2

* Right front speaker output (-) - terminal 6 X2

* Left rear speaker output (+) - terminal 15 X2

* Left rear speaker output (-) - terminal 14 X2

* Right rear speaker output (+) - terminal 16 X2

* Right rear speaker output (-) - terminal 8 X2

* Front center speaker output (+) - terminal 13 X2

* Front center speaker output (-) - terminal 12 X2

* Right rear midrange speaker output (+) - terminal 3 X2

* Right rear midrange speaker output (-) - terminal 2 X2

* Left rear midrange speaker output (+) - terminal 11 X2

* Left rear midrange speaker output (-) - terminal 10 X2

* Left or rear subwoofer speaker output (+) - terminal 1 X1

* Left or rear subwoofer speaker output (-) - terminal 2 X1

* Right subwoofer speaker output (+) - terminal 7 X1

* Right subwoofer speaker output (-) - terminal 3 X1

瀚慖f less than the specified value, test both circuits of the affected speaker for a short to ground.

4. If all circuits test normal, reconnect all harness connectors at the amplifier.

5. Radio ON, disconnect the appropriate speaker.

6. Test for 5.0-7.5 volts between the signal circuit terminals and ground.

瀚慖f less then the specified range test the circuit for an open/high resistance. If the circuit tests normal, replace the amplifier.

瀚慖f greater then the specified range test the circuit for a short to voltage. If the circuit tests normal, replace the amplifier.

7. If the circuit tests normal, replace the appropriate speaker.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Speaker Replacement Reference (See: Accessories and Optional Equipment/Testing and Inspection/Symptom Related Diagnostic

Procedures/Cellular, Entertainment, and Navigation/Speaker Replacement Reference)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for Amplifier and Radio replacement, setup, and

programming

B1035

DTC B1025-B1095

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.