2010 Land Rover Range Rover (LM) V8-5.0L Technical Service Bulletin # TECLTB00491 Date: 121116

2010 Land Rover Range Rover (LM) V8-5.0L Technical Service Bulletin # TECLTB00491 Date: 121116

Suspension System - Air Suspension Compressor Failure

TECHNICAL BULLETIN

LTB00491NAS1

16 NOV 2012

SECTION: 204-05

Air Suspension System Compressor Failure

AFFECTED VEHICLE RANGE:

VIN: 6A198058 - CA393639

Range Rover (LM)

Model Year: 2006 - 2012

CONDITION SUMMARY:

Situation:

The air suspension system may be inoperative and Suspension Fault may be displayed in the message center.

Cause:

This may be cause by an air suspension system compressor failure due to over running

Action:

In the event of a customer concern of the above, refer to the Repair Procedure outlined below.

PARTS:

LR041777 ................ Air compressor kit Qty: 1

TOOLS:

IDS with latest IDS-DVD and Calibration File; first available on DVD131.06 v.117

Land Rover-approved Midtronics Vehicle Power Supply

Refer to Workshop Manual for any required special tools

WARRANTY:

NOTE:

Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only.

Always refer to DDW to obtain the latest repair time.

DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.

Normal Warranty policies and procedures apply

REPAIR PROCEDURE

1. NOTE: Do not carry out the air suspension system depressurize.

Refer to Workshop Manual section 204-05, steps 1-7 only, and replace the air suspension compressor.

2010 Land Rover Range Rover (LM) V8-5.0L Page 2

2. Connect the air suspension pipe to the AMK compressor.

3. Install the four (4) air suspension system compressor retaining bolts.

^ Tighten to 10Nm (7.4 lbf ft).

4. Install the valve block assembly.

^ Connect the AMK harness connectors the same as the Hitachi compressor.

5. Install a new air suspension system compressor relay in the luggage compartment fuse box.

6. CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform these steps may cause damage to control

modules in the vehicle.

CAUTION:

2010 Land Rover Range Rover (LM) V8-5.0L Page 3

A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module

programming. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.

7. Turn ignition 'ON' (engine not running).

8. NOTE: IDS must be loaded with DVD131.06 v.117 or later.

Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.

9. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.

10. From the Session Type selection screen, choose 'Diagnosis'.

11. Select the 'Selected Symptoms' tab, and then select:

^ Service Function

12. Select 'continue'.

13. Select the 'Recommendations' tab.

14. CAUTION: During this procedure, if SDD presents a

question regarding compressor type, always select the type/manufacturer for the compressor being fitted to the vehicle as part of this repair,

which under all circumstances should be an AMK compressor type. If unsure select 'EXIT' at this prompt and repeat this process after the facts

are known. Failure to make the correct compressor type selection will cause SDD to install incorrect software. From the Recommendations tab,

select 'Run' to perform the Air suspension - Air suspension compressor replacement function.

^ Follow all on-screen instructions to complete this task.

15. Exit the current session.

16. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.