Monday, January 21, 2019

2010 Land Rover LR2 (LF) L6-3.2L Technical Service Bulletin # Q0812 Date: 100121

2010 Land Rover LR2 (LF) L6-3.2L Technical Service Bulletin # Q0812 Date: 100121



Campaign - Engine Vent Hose Coolant Leak



No.: Q081



2010 Land Rover LR2 (LF) L6-3.2L Page 61



Issue: 2



Date: 21 JAN 2010



ISSUE '2' CHANGES ARE HIGHLIGHTED IN GRAY



THIS SERVICE ACTION IS VALID FOR A LIMITED TIME ONLY



AND WILL EXPIRE 30 NOVEMBER 2011



SECTION: 303



SERVICE ACTION: Engine Vent Hose Coolant Leak



AFFECTED VEHICLE RANGE:



LR2 (LF) VIN: 8H000001-AH154175



Model Year: 2008 - 2010



CONDITION SUMMARY:



Situation:



A potential concern has been identified with a number of LR2 vehicles regarding a coolant leak from the quick connector joint securing a vent hose



to the engine.



The coolant leak is a drip; therefore, the vehicle will lose coolant over an extended period of time. The loss in coolant could lead to engine



overheating issues which in turn could trigger the reduced performance strategy.



Action:



Retailers are required to HOLD all affected vehicles in the above VIN range that are in their control and refrain from releasing the vehicles for new



or used vehicle sale pending completion of the rework action detailed in this Technical Bulletin. Vehicles must not be released until inspecting, and



if necessary replacing, the vent hose assembly. Affected vehicles in the hands of owners should be repaired at the next available opportunity. At the



time of customer appointment, ensure that all outstanding service campaigns for each individual vehicle are identified and allocate sufficient time



and resources to complete all campaigns.



For cars in Retailer inventory, this Service Action should be performed in conjunction with the vehicle Pre- Delivery Inspection (PDI).



PARTS:



TOOLS:



Refer to Workshop Manual (GTR) for any required special tools



WARRANTY:



NOTE:



Always check DDW to verify that the vehicle is affected by this Action prior to undertaking any repairs. Repair procedures are under constant



review, and therefore times / prices are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the



latest repair time.



Warranty claims should be submitted quoting Program Code 'Q081' together with the relevant Option Code. As Option Codes are used, there is no



requirement to enter parts or labor; these are provided for information only. The option including drive in/drive out allowance may only be claimed



if the vehicle is brought back into the workshop for this action alone to be undertaken.



This Service Action is valid for two (2) years only and will expire 30 November 2011. Warranty claims up to this date must be submitted for



payment within 30 days of completion of the repair. Refer to Service Bulletins SWA09-13 / SWAO9-13C for further administration details.



REPAIR PROCEDURE



2010 Land Rover LR2 (LF) L6-3.2L Page 62



INSPECT / REPLACE ENGINE VENT HOSE



1. Open the hood.



NOTE:



Global Technical Reference (GTR) lookup sequence is as follows:



GTR Home > NAS > LF-LR2 > Service Information > Model Year > Workshop Manual



2. Refer to Workshop Manual (GTR) section 501-05 and remove the engine cover.



3. Inspect the quick connector securing the vent hose to the engine: (Figure 1)



^ If the connector is gray, continue to step 4.



^ If the connector is black, continue to step 11.



WARNING:



Since injury such as scalding could be caused by escaping steam or coolant, do not remove the filler cap from the coolant expansion tank while



the system is hot.



4. Release the quick connector joint securing the vent hose to the coolant expansion tank.



5. Remove the vent hose from the expansion tank.



6. Release the quick connector joint securing the vent hose to the engine. (Figure 2)



7. Remove and discard the vent hose.



8. Install new vent hose to the engine.



9. Install new vent hose to the expansion tank.



10. Check coolant level:



^ Top up coolant level if necessary.



11. Refer to Workshop Manual (GTR) section 501-05 and install the engine cover.



12. Close the hood.



2010 Land Rover LR2 (LF) L6-3.2L Page 63

No comments:

Post a Comment